How to Test Your Water: A Complete Guide for City and Well Water
What's really in your water? How to read your city water report, when and what to test on a private well, what the numbers mean, and which system fits your results.
On this page
Key takeaways
- City water: start with your utility's free annual water quality report (Consumer Confidence Report). Add your own test for what happens in your pipes, such as lead and hardness.
- Private well: nobody tests it for you. Test at least once a year for bacteria, nitrate, pH and hardness, and once for metals like arsenic, iron and manganese.
- Use a certified lab for decisions; home test kits are a good first look.
- Match the treatment to your results. The right system depends on what's actually in your water.
Every good water treatment decision starts with the same question: what's actually in your water? Without that answer, it's easy to buy a system that fixes a problem you don't have, or misses the one you do.
This guide walks you through testing step by step: where to find free data, when to test yourself, what to test for on city or well water, how to read the numbers, and what to do with the results.
City water or well water?
Where your water comes from decides where you start.
- City (municipal) water is treated and tested by your utility, which must meet federal drinking water standards. It's usually disinfected with chlorine or chloramine. What the utility can't control is what happens in the pipes between the street and your tap.
- Private well water isn't regulated by the EPA. The EPA's private well guidance is clear that testing and treatment are the owner's responsibility. Wells can change over time, after heavy rain, drought, nearby construction or flooding.
Step 1 for city water: read your water quality report
Community water systems must send customers a Consumer Confidence Report (CCR), an annual water quality report, by July 1 each year. It lists what the utility found in the previous year's testing and how that compares with federal limits. You can usually find it on your utility's website or through the EPA's CCR page.
When you read it, look for:
- Disinfectant: chlorine or chloramine. This decides which carbon filter you need.
- Hardness: sometimes listed as calcium carbonate in mg/L or ppm. Divide by 17.1 for grains per gallon.
- Detected contaminants: anything listed near its limit, such as nitrate, arsenic or disinfection by-products.
- Lead and copper: reported as the 90th percentile of homes tested.
Why test at home anyway? The report describes water leaving the treatment plant. Lead, copper and some taste problems come from the plumbing in or near your home, so a tap sample tells you what you're really drinking.
Step 1 for well water: test, then test again
For private wells, a lab test is the only reliable starting point. A sensible routine:
| When | What to test |
|---|---|
| Every year | Total coliform bacteria, nitrate, pH, total dissolved solids (TDS) |
| Once, then every few years | Hardness, iron, manganese, arsenic, sulfate, chloride, and any local concerns such as uranium, radon or fluoride |
| After flooding, repairs or a change in taste, color or smell | Bacteria and the parameters linked to the change |
| Before and after installing treatment | The contaminants you're treating, to confirm the system works |
Your state or county health department can recommend certified labs and often knows which contaminants are common in your area.
Lab test or home test kit?
| Home test kit or meter | Certified lab test | |
|---|---|---|
| Good for | Quick checks: hardness, pH, chlorine, TDS | Decisions: bacteria, metals, arsenic, nitrate, lead |
| Accuracy | Approximate | Precise, with detection limits |
| Speed | Minutes | Days to two weeks |
| Use it to | Spot a problem or monitor a system | Choose and size a treatment system |
A simple TDS meter is also a handy way to see whether a reverse osmosis system is still working: compare tap and RO water a few times a year.
What the numbers on your test mean
These are the parameters that most often decide which system you need. The reference values come from EPA standards: enforceable limits for health-related contaminants, and secondary guidelines for taste, odor, staining and corrosion.
| Parameter | Reference | What a high (or low) value means |
|---|---|---|
| Hardness | Above ~7 gpg (120 mg/L) is considered hard | Scale, spotty dishes, poor lather |
| pH | 6.5 to 8.5 (secondary) | Low pH: corrosive water, blue-green stains |
| TDS | 500 mg/L (secondary) | Salty or flat taste, scale |
| Iron | 0.3 mg/L (secondary) | Orange stains, metallic taste |
| Manganese | 0.05 mg/L (secondary) | Black or brown stains |
| Sulfate | 250 mg/L (secondary) | Bitter taste |
| Hydrogen sulfide | No standard; noticeable at very low levels | Rotten-egg smell |
| Arsenic | 10 ppb (federal limit) | Needs dedicated treatment |
| Nitrate | 10 mg/L as nitrogen (federal limit) | Common near farmland; needs dedicated treatment |
| Total coliform | Should be absent | Possible contamination path; disinfect and investigate |
The full list of federal limits is in the EPA's National Primary Drinking Water Regulations. If a health-related contaminant shows up above its limit, talk to your local health department as well as a water treatment specialist.
From results to the right system
| Your result | Typical solution | Where to look |
|---|---|---|
| Chlorine or chloramine, taste and odor | Whole house carbon filter | Whole house water filters |
| Hard water | Water softener or salt-free conditioner | Water softeners, salt-free conditioners |
| High TDS, nitrate, or you want the purest drinking water | Reverse osmosis | Under-sink RO systems |
| Iron, manganese or sulfur smell | Iron or metal removal filter, fine mesh softener | Crystal Quest Metal Removal |
| Low pH | Acid neutralizer | Crystal Quest Acid Neutralizing |
| Arsenic | Arsenic media or RO | Arsenic guide |
| Bacteria (well) | Shock-chlorinate, find the cause, then UV | UV water sterilizers |
Most homes need two or three of these together, in the right order: sediment first, then iron or pH correction, then softening, carbon, and UV last. A whole house bundle combines several stages with matched sizes.
How to take a good sample
- Use the bottles and instructions from the lab; some tests need special preservatives.
- For bacteria, remove the aerator, run the cold tap a few minutes and avoid touching the bottle's inside or cap.
- For lead and copper, take a "first draw" sample from water that sat in the pipes for at least six hours.
- Sample before any treatment if you want to know your raw water, and after treatment to check your system.
- Get the samples to the lab within the time they specify, usually within a day for bacteria.
Common questions
How much does a water test cost?
A basic home kit costs little; lab panels range from a basic bacteria and nitrate test to comprehensive panels covering dozens of parameters. Your health department or a local lab can tell you which panel fits your situation.
How often should I test city water?
Read your utility's report every year. Test at the tap if you have older plumbing, notice a change in taste or color, or are choosing a treatment system.
Can I tell if my water is safe by how it looks or tastes?
No. Some of the contaminants that matter most, such as arsenic, nitrate, lead and bacteria, have no color, taste or smell. Testing is the only way to know.
What is TDS, and is high TDS bad?
TDS stands for total dissolved solids: everything dissolved in the water, from calcium and magnesium to salts. High TDS mostly affects taste and scale. It doesn't tell you which substances are present, so use it together with a full test.
Do I need to test after installing a filter?
Yes. A follow-up test confirms the system is reducing what you bought it for, and it gives you a baseline to compare against later.
Got your results? Send them to us or call +1 657-837-2821 (Mon-Fri, 9-5 EST). We'll help you read them and recommend the system that matches your water, even if that's a smaller one.
Shop the systems in this guide
Aquasure
Aquasure Fortitude Pro Whole House Water Filter, 600K-1.5M Gallon
From $699.99
Aquasure
Aquasure Harmony Whole House Water Softener, 32,000-72,000 Grain
From $539.99
Aquasure
Aquasure Premier 4-Stage Under-Sink RO System, 75 or 100 GPD
From $199.99
Aquasure
Aquasure Quantum Whole House UV Water Sterilizer, 8-18 GPM
From $169.99
